Plumber's Essentials: Your Key to Bathtub Installation

Click Here

What are your thoughts on How to Install a Bathtub Yourself?


Installing A Bathtub
Setting up a tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging task. If the old tub is easily easily accessible, the job can move immediately; if you need to open up a wall to remove the old tub and position the brand-new tub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the new one. See to it you have certified yourself for the work as well as fit trying it. Rather than employing a specialist to take over a halfway-completed task, it is much better to take into consideration employing one before you start. Chances are you might require an expert plumber to make tube connections.
This post will assist you install a new bathtub in your shower room if you have actually currently bought a new bathtub and do not require to alter the plan of your previous water pipes.
Your tools and also product list ought to consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome due to the restricted access that is typically the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
    Prior to going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer offered backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous type needs to be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Mounting the Bath tub


    Utilizing both wood boards under its feet, position the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
    The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub till the spirit level checks out level.
    To install taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the various other tap.
    Activate the water supply and also check all joints as well as new pipework for leakages as well as tighten them if required. Load the bathtub and additionally check the overflow outlet and also the regular outlet for leakages.
    Lastly, take care of the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has been utilized a minimum of once as this will settle it right into its final position.

    Getting ready for the Setup


    First of all, the supporting frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to stop strain on the tub.
    Fit the versatile faucet ports to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its final placement.

    Tiling Around the Bathtub


    In the location where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, triggering the water to pass through the wall between the bath and also the tiling, resulting in problems with moisture and also possible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to assimilate your components and also installations. They are marketed in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this movement before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof adhesive and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    We were shown that editorial on Tools You Need to Install a New Bathtub from a good friend on a different web page. Feel free to take the opportunity to promote this page if you liked it. We take joy in reading our article about Tools You Need to Install a New Bathtub .


    Got a leak? Call!

    Leave a Reply

    Your email address will not be published. Required fields are marked *